Leak detector spray

LEAK DETECTOR SPRAY


Leaks in compressed air and gas flow systems can be detected by using the high-quality presto Leak Detector Spray. Bubble will indicate where the leak is. The foam is easy to wash off with water. It leaves no residue that could impede repair work. DVGW certificate no. NG/5170BR0105.

For use on:
Pipes, hoses, tyres, tanks, compressors, pressure switch, compressed air bottles, refrigerant circuits and systems with combustible gases.

QUALITY AND PROPERTIES

  • Non-combustible
  • Non-corrosive
  • Slightly alkaline and foam forming
  • Surplus spray can easily be washed off with water
  • Contains rust-protective inhibitors
  • Solvent free
  • Good spreading rate
  • Works up to outdoor temperatures of 0°C
  • DVGW-certified (German Association for gas and water applications)
  • TRG 300 compliant

PHYSICAL AND CHEMICAL DATA

  • Basis: Tenside Solution
  • Colour: transparent
  • Smell:characteristic
  • Appearance:foam
  • Relative density at 20°C:02 g/ml
  • Yield:8 g/sec.
  • Vapour pressure at 20°C:8 – 9 bar
  • pH-value:0 – 7.5
  • Residual pressure:5 – 4.5 bar
  • Storage stability:
    10 years if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%)
  • Size:
    aerosol can, maximum nominal volume 300 ml

ENVIRONMENT AND LABELLING

Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.

Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as “special refuse”.

Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II,

USING INSTRUCTIONS

Before use, carefully read and observe the warning texts on the label!

Application:

  • Bring can to room temperature.
  • Operating temperature 5° to 30°C.
  • Shake can for 2 minutes before use.
  • Spray the object that needs to be examined from the usual distance until a sealed film has formed.
  • Bubbles will indicate the leaks.
  • Finally, surplus foam can be washed off with water.

TIPS FOR SPRAY PAINTING

Protect the object and the surrounding area from spray mist.
Temperature should range between +10°C and +25°C, max. air humidity 60 %.

Store in a dry place. Protect from direct sunlight and other sources of heat. Use only during dry weather, in places protected from the wind, and in well-ventilated rooms. Follow the warning texts on the labels!

ORDER INFORMATION

Color   Product   Bundle   Art.No. 
 *  Lecksuch-Spray 300  300 ml  157219
 * no color identification possible

The presentation of colors may deviate from the original color.

EXAMPLES FOR USE

DISCLAIMER OF LIABILITY

This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. MOTIP DUPLI is let off the liability, unless the liability-based incident is caused by a fault incurred to MOTIP DUPLI.

For any further technical questions call our hotline +49 (0) 62 66 75-266 from Monday to Thursday from 9 h a.m. to 3 h p.m. or on Friday until 12 h p.m.

As of: May 22, 2014
This release replaces all eventually earlier issued versions.

 

PORUDŽBENI BROJEVI

Color   Product   Bundle   Art.No. 
 *  Lecksuch-Spray 300  300 ml  157219
 * no color identification possible

The presentation of colors may deviate from the original color.