Lak za plastiku

LAK ZA PLASTIKU


Poseban lak visokog kvaliteta, razvijen za farbanje i direktno nanošenje na plastične predmete bez posebnih osnovnih premaza za plastiku. Pogodan za upotrebu na sledećim vrstama tvrde plastike: Poliuretan (PUR), Polistiren (PS), Poliamid (PA), Polipropilen guma modifikovana (EPDM), Akril butadien stiren plastika (ABS), Plastika ojačana vlaknima (GFK), Tvrda polivinil hlorid (Tvrda-PVC).

Pravilnim čišćenjem plastičnih predmeta poboljšava se prianjanje laka.

Baza: Nitrokombi
Pokrivenost: U zavisnosti od rapavosti i boje podlove 400 ml je dovoljno za oko 1 m²

QUALITY AND PROPERTIES

  • High-quality special lacquer for the painting of car parts of coatable hard plastic
  • Very good coverage
  • Excellent adhesion, no special primer necessary
  • Good flow, smooth surface
  • Quick-drying
  • Weather-resistant, light-proof, UV-resistant
  • Scratch-, shock- and impact-resistant

PHYSICAL AND CHEMICAL DATA

  • Basis of the binder:nitro-combi
  • Colour: diverse
  • Smell:solvent
  • Degree of gloss(at measurement angle 60° acc. to DIN 67530):
    satin gloss 30-40 gloss units
  • Efficiency:
    Depending on consistence and color of the ground:
    400 ml are sufficient for approx. 1.0 m²
  • Drying time (at 20°C, 50% relative air humidity):
    Dust-dry: after approx. 10 minutes
    Dry to touch: after approx. 30 minutes
    Cured: after approx. 2 hours
    The drying time depends on surrounding temperature, air humidity and thickness of the applied coat.
  • Storage stability:
    10 years if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%)
  • Size: aerosol cans, maximum nominal volume 400 ml

ENVIRONMENT AND LABELLING

Environmentally compatible: MOTIP DUPLI is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.

Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as “special refuse”.

Labelling: All products of MOTIP DUPLI comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II,

USING INSTRUCTIONS

The most DUPLI-COLOR spray paints have a so-called no-spray ring or a tamper-proof cap. This is to avoid unauthorized use. Please see the corresponding advises on the cap or on the label.
Before use, carefully read and observe the warning texts on the label!

Application

  • Clean the surface, it has to be absolutely free from fat, wax and dirt.
  • Remainders of polish or other car care products will have a negative influence on the adhesion.
  • If necessary (scratches, damages etc.) sand the surface, eventually fill with putty and prime with structure spray.
  • Before use, shake can vigorously for at least 2 minutes after you hear the noise of the mixing balls.
  • Test spray at an invisible spot.
  • Apply several thin cross-coats from a distance of 25 cm. Let lift off for 5 minutes after every coat.
  • Do not spray over synthetic paints!

TIPS FOR SPRAY PAINTING

Protect the object and the surrounding area from spray mist. When painting small areas it is recommended that a piece of card is used as a mask, with a hole cut in it slightly larger than the area to be sprayed. The mask should be held 1 to 2 cm from the surface. With this method, the mainly part of the spray mist is brought under control. It recommends to mask parts not to be lacquered, to protect the surrounding against the spray mist.

The aerosol can should have room temperature.

Temperature should range between +10°C and +25°C, max. air humidity 60 %.

Store in a dry place. Protect from direct sunlight and other sources of heat. Use only during dry weather, in places protected from the wind, and in well-ventilated rooms. Follow the warning texts on the labels!

ORDER INFORMATION

Color   Product   Bundle   Art.No. 
 DC Kunststoff dunk.grau II 400  400 ml  406231
 DC Kunststoff dunkelgrau 400  400 ml  406217
 DC Kunststoff lichtgrau 400  400 ml  406422
 DC Kunststoff schwarz 400  400 ml  400116
 * no color identification possible

The presentation of colors may deviate from the original color.

EXAMPLES FOR USE

DISCLAIMER OF LIABILITY

This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. MOTIP DUPLI is let off the liability, unless the liability-based incident is caused by a fault incurred to MOTIP DUPLI.

For any further technical questions call our hotline +49 (0) 62 66 75-266 from Monday to Thursday from 9 h a.m. to 3 h p.m. or on Friday until 12 h p.m.

As of February 26, 2016
This release replaces all eventually earlier issued versions.

 

PORUDŽBENI BROJEVI

Color   Product   Bundle   Art.No. 
 DC Kunststoff dunk.grau II 400  400 ml  406231
 DC Kunststoff dunkelgrau 400  400 ml  406217
 DC Kunststoff lichtgrau 400  400 ml  406422
 DC Kunststoff schwarz 400  400 ml  400116
 * no color identification possible

The presentation of colors may deviate from the original color.